{"title":"PCB Standoffs","description":"\u003cp\u003eThreaded spacers that hold a printed circuit board off its chassis, stack two boards at a fixed pitch, or carry a panel inside an enclosure. Every listing gives thread size, body length, across-flats dimension, thread configuration and material, with each figure in both millimetres and inches.\u003c\/p\u003e\n\u003ch3\u003eChoosing the material\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eNylon 6\/6\u003c\/strong\u003e is non-conductive and non-magnetic, which is why it is the default wherever the standoff sits close to live traces. It absorbs moisture over time and softens above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBrass\u003c\/strong\u003e conducts, so a brass standoff can double as a chassis ground path. It machines cleanly and holds an accurate thread at M2 and M2.5, where steel tends to tear.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e304 stainless\u003c\/strong\u003e is what to use when the assembly is handled, vibrated or exposed. Stainless threads gall under speed or load — back the driver off and use an anti-seize compound on anything you expect to disassemble.\u003c\/p\u003e\n\u003ch3\u003eMale-female or female-female\u003c\/h3\u003e\n\u003cp\u003eA male-female standoff carries a stud at one end and an internal thread at the other, so a column of them stacks without extra hardware. Female-female takes a screw from both directions and is the safer default when you are not sure which way the assembly comes apart.\u003c\/p\u003e\n\u003ch3\u003eMetric or imperial\u003c\/h3\u003e\n\u003cp\u003eUS boards run on both. M3 and #4-40 are close in diameter but are not interchangeable — the pitch differs and cross-threading destroys the internal thread. If you are matching an existing board, measure before you order; our \u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003emetric to imperial conversion table\u003c\/a\u003e covers the sizes that get confused most often.\u003c\/p\u003e\u003ch2\u003eShop by thread size\u003c\/h2\u003e\u003cp\u003eSize pages carry the across-flats dimension, available lengths and the thread warning for that size: \u003ca href=\"\/collections\/m2-5-standoffs\"\u003eM2.5\u003c\/a\u003e, \u003ca href=\"\/collections\/m3-standoffs\"\u003eM3\u003c\/a\u003e, \u003ca href=\"\/collections\/4-40-standoffs\"\u003e#4-40\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"m2-5-nylon-6-6-hex-standoff-male-female-6mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Male-Female, 6mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 6mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 6mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e6 mm (0.236 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.148 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522775773415,"sku":"PF-STD-M25-NY-MF-6","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_a3e85c2a-d29b-40c8-8e8c-644ba1a2c7e4.jpg?v=1787882510"},{"product_id":"m2-5-nylon-6-6-hex-standoff-male-female-8mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Male-Female, 8mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 8mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 8mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e8 mm (0.315 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.197 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522775838951,"sku":"PF-STD-M25-NY-MF-8","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_0fcbea6e-5034-47ef-a876-6dc2c240a912.jpg?v=1787882507"},{"product_id":"m2-5-nylon-6-6-hex-standoff-male-female-10mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Male-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 10mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.247 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522775871719,"sku":"PF-STD-M25-NY-MF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_dd50e37b-b01b-4b9a-a1b9-00654b335228.jpg?v=1787882505"},{"product_id":"m2-5-nylon-6-6-hex-standoff-male-female-12mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Male-Female, 12mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 12mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 12mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e12 mm (0.472 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.296 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522775937255,"sku":"PF-STD-M25-NY-MF-12","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_c29a8240-698a-4222-97b4-fe94fc95bd20.jpg?v=1787882502"},{"product_id":"m2-5-nylon-6-6-hex-standoff-male-female-15mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Male-Female, 15mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 15mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 15mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e15 mm (0.591 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.37 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776002791,"sku":"PF-STD-M25-NY-MF-15","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_caabad79-93a6-4fb3-90b1-5d0bda99b7ec.jpg?v=1787882500"},{"product_id":"m2-5-nylon-6-6-hex-standoff-male-female-20mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Male-Female, 20mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 20mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Male-Female, 20mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e20 mm (0.787 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.494 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776199399,"sku":"PF-STD-M25-NY-MF-20","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_1e98d8cb-4c5b-4676-ae95-c0c77c8385e8.jpg?v=1787882497"},{"product_id":"m2-5-nylon-6-6-hex-standoff-female-female-6mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Female-Female, 6mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 6mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 6mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e6 mm (0.236 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.148 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776232167,"sku":"PF-STD-M25-NY-FF-6","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_36b37280-70c6-488e-9282-d75b2bced16c.jpg?v=1787882494"},{"product_id":"m2-5-nylon-6-6-hex-standoff-female-female-8mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Female-Female, 8mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 8mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 8mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e8 mm (0.315 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.197 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776297703,"sku":"PF-STD-M25-NY-FF-8","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_21ecd672-e2f8-4751-9960-9afc045e0a29.jpg?v=1787882491"},{"product_id":"m2-5-nylon-6-6-hex-standoff-female-female-10mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Female-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 10mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.247 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776363239,"sku":"PF-STD-M25-NY-FF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_4c541924-5c26-4a86-846f-213bd18e3239.jpg?v=1787882489"},{"product_id":"m2-5-nylon-6-6-hex-standoff-female-female-12mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Female-Female, 12mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 12mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 12mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e12 mm (0.472 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.296 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776396007,"sku":"PF-STD-M25-NY-FF-12","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_833ede50-3fd2-4756-8105-2b769327c353.jpg?v=1787882486"},{"product_id":"m2-5-nylon-6-6-hex-standoff-female-female-15mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Female-Female, 15mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 15mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 15mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e15 mm (0.591 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.37 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776461543,"sku":"PF-STD-M25-NY-FF-15","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_c70b9363-e974-4fb1-b7a8-9c04c4ef6986.jpg?v=1787882484"},{"product_id":"m2-5-nylon-6-6-hex-standoff-female-female-20mm","title":"M2.5 Nylon 6\/6 Hex Standoff, Female-Female, 20mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 20mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Nylon 6\/6 Hex Standoff, Female-Female, 20mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e20 mm (0.787 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.494 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776527079,"sku":"PF-STD-M25-NY-FF-20","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_8e4efd1a-fa94-4e4a-ac87-1d46131a28d8.jpg?v=1787882481"},{"product_id":"m3-nylon-6-6-hex-standoff-male-female-5mm","title":"M3 Nylon 6\/6 Hex Standoff, Male-Female, 5mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 5mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 5mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e5 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.149 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776559847,"sku":"PF-STD-M3-NY-MF-5","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_9e43ed72-638b-40ce-ae4d-39da5986f88e.jpg?v=1787882479"},{"product_id":"m3-nylon-6-6-hex-standoff-male-female-6mm","title":"M3 Nylon 6\/6 Hex Standoff, Male-Female, 6mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 6mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 6mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e6 mm (0.236 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.179 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776625383,"sku":"PF-STD-M3-NY-MF-6","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_4bcff225-7ce7-4661-a6d8-2b5941ae72e2.jpg?v=1787882476"},{"product_id":"m3-nylon-6-6-hex-standoff-male-female-8mm","title":"M3 Nylon 6\/6 Hex Standoff, Male-Female, 8mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 8mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 8mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e8 mm (0.315 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.239 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776690919,"sku":"PF-STD-M3-NY-MF-8","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_28261a53-0a4b-46a0-8e6e-6928196dcd7b.jpg?v=1787882473"},{"product_id":"m3-nylon-6-6-hex-standoff-male-female-10mm","title":"M3 Nylon 6\/6 Hex Standoff, Male-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 10mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.299 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776723687,"sku":"PF-STD-M3-NY-MF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_54014cef-ce60-42c3-af10-89bca19f372d.jpg?v=1787882470"},{"product_id":"m3-nylon-6-6-hex-standoff-male-female-12mm","title":"M3 Nylon 6\/6 Hex Standoff, Male-Female, 12mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 12mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 12mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e12 mm (0.472 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.358 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776789223,"sku":"PF-STD-M3-NY-MF-12","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_ddc84eb6-4562-4463-ab9c-71788c8d4b81.jpg?v=1787882468"},{"product_id":"m3-nylon-6-6-hex-standoff-male-female-15mm","title":"M3 Nylon 6\/6 Hex Standoff, Male-Female, 15mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 15mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 15mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e15 mm (0.591 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.448 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776854759,"sku":"PF-STD-M3-NY-MF-15","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_72b473c5-4b08-4a7e-8193-26639128a659.jpg?v=1787882466"},{"product_id":"m3-nylon-6-6-hex-standoff-male-female-20mm","title":"M3 Nylon 6\/6 Hex Standoff, Male-Female, 20mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 20mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 20mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e20 mm (0.787 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.597 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776887527,"sku":"PF-STD-M3-NY-MF-20","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main_a1d30351-b503-47bb-9d50-3bff58d0afdc.jpg?v=1787882463"},{"product_id":"m3-nylon-6-6-hex-standoff-male-female-25mm","title":"M3 Nylon 6\/6 Hex Standoff, Male-Female, 25mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 25mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Male-Female, 25mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e25 mm (0.984 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.747 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522776953063,"sku":"PF-STD-M3-NY-MF-25","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-mf-natural-main.jpg?v=1787882461"},{"product_id":"m3-nylon-6-6-hex-standoff-female-female-5mm","title":"M3 Nylon 6\/6 Hex Standoff, Female-Female, 5mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 5mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 5mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e5 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.149 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777018599,"sku":"PF-STD-M3-NY-FF-5","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_3dbb8cac-0275-4130-a3c3-419d81749b2b.jpg?v=1787882458"},{"product_id":"m3-nylon-6-6-hex-standoff-female-female-6mm","title":"M3 Nylon 6\/6 Hex Standoff, Female-Female, 6mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 6mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 6mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e6 mm (0.236 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.179 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777084135,"sku":"PF-STD-M3-NY-FF-6","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_5537e545-0dab-4f21-8c2d-7041414cced4.jpg?v=1787882456"},{"product_id":"m3-nylon-6-6-hex-standoff-female-female-8mm","title":"M3 Nylon 6\/6 Hex Standoff, Female-Female, 8mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 8mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 8mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e8 mm (0.315 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.239 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777149671,"sku":"PF-STD-M3-NY-FF-8","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_3800cf85-bf2f-42cf-90f0-71c13d5f4f9d.jpg?v=1787882453"},{"product_id":"m3-nylon-6-6-hex-standoff-female-female-10mm","title":"M3 Nylon 6\/6 Hex Standoff, Female-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 10mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.299 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777215207,"sku":"PF-STD-M3-NY-FF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_46f03b22-f3c8-4326-ad25-246f9f85914c.jpg?v=1787882450"},{"product_id":"m3-nylon-6-6-hex-standoff-female-female-12mm","title":"M3 Nylon 6\/6 Hex Standoff, Female-Female, 12mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 12mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 12mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e12 mm (0.472 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.358 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777280743,"sku":"PF-STD-M3-NY-FF-12","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_72bc2f3d-b3a0-404e-9bf7-eeca88e9f3b2.jpg?v=1787882447"},{"product_id":"m3-nylon-6-6-hex-standoff-female-female-15mm","title":"M3 Nylon 6\/6 Hex Standoff, Female-Female, 15mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 15mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 15mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e15 mm (0.591 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.448 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777313511,"sku":"PF-STD-M3-NY-FF-15","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_c871340e-1fdf-4e06-9cd7-e58917756805.jpg?v=1787882445"},{"product_id":"m3-nylon-6-6-hex-standoff-female-female-20mm","title":"M3 Nylon 6\/6 Hex Standoff, Female-Female, 20mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 20mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 20mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e20 mm (0.787 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.597 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777379047,"sku":"PF-STD-M3-NY-FF-20","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main_02694a49-0de3-4e5d-ad53-028fea6dcaff.jpg?v=1787882442"},{"product_id":"m3-nylon-6-6-hex-standoff-female-female-25mm","title":"M3 Nylon 6\/6 Hex Standoff, Female-Female, 25mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 25mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Nylon 6\/6 Hex Standoff, Female-Female, 25mm\u003c\/strong\u003e — a hex standoff in Nylon 6\/6 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e25 mm (0.984 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eNylon 6\/6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eNatural\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e120 °C (248 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlammability rating\u003c\/th\u003e\n\u003ctd\u003eUL94 V-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e0.747 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e3926.90.9985\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Nylon 6\/6\u003c\/h3\u003e\u003cp\u003eNylon 6\/6 is non-conductive and non-magnetic, which is why it is the default for standoffs that sit close to live traces. It absorbs moisture over time and loses stiffness above roughly 85 °C, so it is not a structural choice.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777444583,"sku":"PF-STD-M3-NY-FF-25","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/nylon-ff-natural-main.jpg?v=1787882439"},{"product_id":"m2-5-brass-hex-standoff-male-female-6mm","title":"M2.5 Brass Hex Standoff, Male-Female, 6mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Brass Hex Standoff, Male-Female, 6mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Brass Hex Standoff, Male-Female, 6mm\u003c\/strong\u003e — a hex standoff in Brass with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e6 mm (0.236 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e1.104 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777477351,"sku":"PF-STD-M25-BR-MF-6","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-mf-main_13210995-a17a-42f1-a061-441027148456.jpg?v=1787882433"},{"product_id":"m2-5-brass-hex-standoff-male-female-10mm","title":"M2.5 Brass Hex Standoff, Male-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Brass Hex Standoff, Male-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Brass Hex Standoff, Male-Female, 10mm\u003c\/strong\u003e — a hex standoff in Brass with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e1.84 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777542887,"sku":"PF-STD-M25-BR-MF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-mf-main_d16a7298-e57d-449a-ae9f-7852b806f4bb.jpg?v=1787882427"},{"product_id":"m2-5-brass-hex-standoff-male-female-15mm","title":"M2.5 Brass Hex Standoff, Male-Female, 15mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Brass Hex Standoff, Male-Female, 15mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Brass Hex Standoff, Male-Female, 15mm\u003c\/strong\u003e — a hex standoff in Brass with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e15 mm (0.591 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e2.76 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777608423,"sku":"PF-STD-M25-BR-MF-15","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-mf-main_385d3387-ffa1-4f79-84a1-40e9f7dc37b6.jpg?v=1787882421"},{"product_id":"m2-5-brass-hex-standoff-female-female-6mm","title":"M2.5 Brass Hex Standoff, Female-Female, 6mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Brass Hex Standoff, Female-Female, 6mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Brass Hex Standoff, Female-Female, 6mm\u003c\/strong\u003e — a hex standoff in Brass with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e6 mm (0.236 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e1.104 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777641191,"sku":"PF-STD-M25-BR-FF-6","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-ff-main_8de74e90-366d-4405-a73e-36f960aa2833.jpg?v=1787882415"},{"product_id":"m2-5-brass-hex-standoff-female-female-10mm","title":"M2.5 Brass Hex Standoff, Female-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Brass Hex Standoff, Female-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Brass Hex Standoff, Female-Female, 10mm\u003c\/strong\u003e — a hex standoff in Brass with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e1.84 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777706727,"sku":"PF-STD-M25-BR-FF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-ff-main_cc4581ba-4106-4f6a-b3bc-7862cbdd3733.jpg?v=1787882409"},{"product_id":"m2-5-brass-hex-standoff-female-female-15mm","title":"M2.5 Brass Hex Standoff, Female-Female, 15mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM2.5 Brass Hex Standoff, Female-Female, 15mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM2.5 Brass Hex Standoff, Female-Female, 15mm\u003c\/strong\u003e — a hex standoff in Brass with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.45 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e15 mm (0.591 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.0 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e2.76 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 2.9 mm (0.114 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M2.5:\u003c\/strong\u003e 2.05 mm (0.081 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #3-48 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777772263,"sku":"PF-STD-M25-BR-FF-15","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-ff-main_4884aa98-7894-4f0f-ab93-8c857b6abe63.jpg?v=1787882403"},{"product_id":"m3-brass-hex-standoff-male-female-5mm","title":"M3 Brass Hex Standoff, Male-Female, 5mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Male-Female, 5mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Male-Female, 5mm\u003c\/strong\u003e — a hex standoff in Brass with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e5 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e1.113 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777805031,"sku":"PF-STD-M3-BR-MF-5","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-mf-main_25405105-e217-4c3c-8b08-952a9447e752.jpg?v=1787882397"},{"product_id":"m3-brass-hex-standoff-male-female-8mm","title":"M3 Brass Hex Standoff, Male-Female, 8mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Male-Female, 8mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Male-Female, 8mm\u003c\/strong\u003e — a hex standoff in Brass with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e8 mm (0.315 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e1.781 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777870567,"sku":"PF-STD-M3-BR-MF-8","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-mf-main_2166dca2-8456-46b8-ba56-be778a7afdac.jpg?v=1787882392"},{"product_id":"m3-brass-hex-standoff-male-female-10mm","title":"M3 Brass Hex Standoff, Male-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Male-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Male-Female, 10mm\u003c\/strong\u003e — a hex standoff in Brass with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e2.226 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777936103,"sku":"PF-STD-M3-BR-MF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-mf-main_355871ec-1a0f-4c5e-80cf-adb35ea9cb7f.jpg?v=1787882387"},{"product_id":"m3-brass-hex-standoff-male-female-15mm","title":"M3 Brass Hex Standoff, Male-Female, 15mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Male-Female, 15mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Male-Female, 15mm\u003c\/strong\u003e — a hex standoff in Brass with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e15 mm (0.591 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e3.34 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522777968871,"sku":"PF-STD-M3-BR-MF-15","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-mf-main_25977e6d-6f19-4185-891d-77f2972ba782.jpg?v=1787882381"},{"product_id":"m3-brass-hex-standoff-male-female-20mm","title":"M3 Brass Hex Standoff, Male-Female, 20mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Male-Female, 20mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Male-Female, 20mm\u003c\/strong\u003e — a hex standoff in Brass with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e20 mm (0.787 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e4.453 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778034407,"sku":"PF-STD-M3-BR-MF-20","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-mf-main_7fd7da4c-c493-40a6-a33c-04d9a8b41752.jpg?v=1787882376"},{"product_id":"m3-brass-hex-standoff-male-female-25mm","title":"M3 Brass Hex Standoff, Male-Female, 25mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Male-Female, 25mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Male-Female, 25mm\u003c\/strong\u003e — a hex standoff in Brass with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e25 mm (0.984 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e5.566 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778099943,"sku":"PF-STD-M3-BR-MF-25","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-mf-main.jpg?v=1787882371"},{"product_id":"m3-brass-hex-standoff-female-female-5mm","title":"M3 Brass Hex Standoff, Female-Female, 5mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Female-Female, 5mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Female-Female, 5mm\u003c\/strong\u003e — a hex standoff in Brass with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e5 mm (0.197 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e1.113 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778132711,"sku":"PF-STD-M3-BR-FF-5","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-ff-main_258b2c56-3b28-4659-918c-9e06e4e62dcc.jpg?v=1787882366"},{"product_id":"m3-brass-hex-standoff-female-female-8mm","title":"M3 Brass Hex Standoff, Female-Female, 8mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Female-Female, 8mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Female-Female, 8mm\u003c\/strong\u003e — a hex standoff in Brass with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e8 mm (0.315 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e1.781 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778198247,"sku":"PF-STD-M3-BR-FF-8","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-ff-main_0ee0744f-f04f-4c4b-af8c-9d4afe3673ec.jpg?v=1787882361"},{"product_id":"m3-brass-hex-standoff-female-female-10mm","title":"M3 Brass Hex Standoff, Female-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Female-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Female-Female, 10mm\u003c\/strong\u003e — a hex standoff in Brass with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e2.226 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778263783,"sku":"PF-STD-M3-BR-FF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-ff-main_9c547575-5f3f-41db-8d06-8d4f20a6bff8.jpg?v=1787882356"},{"product_id":"m3-brass-hex-standoff-female-female-15mm","title":"M3 Brass Hex Standoff, Female-Female, 15mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Female-Female, 15mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Female-Female, 15mm\u003c\/strong\u003e — a hex standoff in Brass with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e15 mm (0.591 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e3.34 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778296551,"sku":"PF-STD-M3-BR-FF-15","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-ff-main_50d34b6b-ee04-4b15-b23a-2f87efafc617.jpg?v=1787882351"},{"product_id":"m3-brass-hex-standoff-female-female-20mm","title":"M3 Brass Hex Standoff, Female-Female, 20mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Female-Female, 20mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Female-Female, 20mm\u003c\/strong\u003e — a hex standoff in Brass with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e20 mm (0.787 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e4.453 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778362087,"sku":"PF-STD-M3-BR-FF-20","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-ff-main_18cfd2ba-fd0b-4871-b18d-fb55eedc6424.jpg?v=1787882346"},{"product_id":"m3-brass-hex-standoff-female-female-25mm","title":"M3 Brass Hex Standoff, Female-Female, 25mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Brass Hex Standoff, Female-Female, 25mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Brass Hex Standoff, Female-Female, 25mm\u003c\/strong\u003e — a hex standoff in Brass with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e25 mm (0.984 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e200 °C (392 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e5.566 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7415.29.0000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Brass\u003c\/h3\u003e\u003cp\u003eBrass conducts, so a brass standoff can serve as a chassis ground path. It machines cleanly, holds thread accurately at small sizes, and will not gall against steel the way stainless can.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778427623,"sku":"PF-STD-M3-BR-FF-25","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/brass-ff-main.jpg?v=1787882339"},{"product_id":"m3-stainless-steel-304-hex-standoff-male-female-10mm","title":"M3 Stainless Steel 304 Hex Standoff, Male-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Stainless Steel 304 Hex Standoff, Male-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Stainless Steel 304 Hex Standoff, Male-Female, 10mm\u003c\/strong\u003e — a hex standoff in Stainless Steel 304 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eStainless Steel 304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStrength grade \/ class\u003c\/th\u003e\n\u003ctd\u003eA2-70\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e400 °C (752 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e2.077 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7318.15.2000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Stainless Steel 304\u003c\/h3\u003e\u003cp\u003e304 stainless resists general atmospheric and indoor corrosion and is non-magnetic in the annealed condition. It is not the right choice for salt spray or chloride exposure — 316 is. Stainless threads can gall under speed or load; back off the driver and use an anti-seize compound on repeated assemblies.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778493159,"sku":"PF-STD-M3-SS-MF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/pcb-standoff-male-female-schematic_a370aa7e-0c44-40e6-9558-278ca8378fcb.png?v=1787757432"},{"product_id":"m3-stainless-steel-304-hex-standoff-male-female-15mm","title":"M3 Stainless Steel 304 Hex Standoff, Male-Female, 15mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Stainless Steel 304 Hex Standoff, Male-Female, 15mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Stainless Steel 304 Hex Standoff, Male-Female, 15mm\u003c\/strong\u003e — a hex standoff in Stainless Steel 304 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e15 mm (0.591 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eStainless Steel 304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStrength grade \/ class\u003c\/th\u003e\n\u003ctd\u003eA2-70\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e400 °C (752 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e3.116 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7318.15.2000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Stainless Steel 304\u003c\/h3\u003e\u003cp\u003e304 stainless resists general atmospheric and indoor corrosion and is non-magnetic in the annealed condition. It is not the right choice for salt spray or chloride exposure — 316 is. Stainless threads can gall under speed or load; back off the driver and use an anti-seize compound on repeated assemblies.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778525927,"sku":"PF-STD-M3-SS-MF-15","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/pcb-standoff-male-female-schematic_ab7a1ee9-337e-48fc-8d0d-14666a265548.png?v=1787757433"},{"product_id":"m3-stainless-steel-304-hex-standoff-male-female-20mm","title":"M3 Stainless Steel 304 Hex Standoff, Male-Female, 20mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Stainless Steel 304 Hex Standoff, Male-Female, 20mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Stainless Steel 304 Hex Standoff, Male-Female, 20mm\u003c\/strong\u003e — a hex standoff in Stainless Steel 304 with male thread at one end and a female thread at the other. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e20 mm (0.787 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eMale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eStainless Steel 304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStrength grade \/ class\u003c\/th\u003e\n\u003ctd\u003eA2-70\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e400 °C (752 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e4.154 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7318.15.2000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Stainless Steel 304\u003c\/h3\u003e\u003cp\u003e304 stainless resists general atmospheric and indoor corrosion and is non-magnetic in the annealed condition. It is not the right choice for salt spray or chloride exposure — 316 is. Stainless threads can gall under speed or load; back off the driver and use an anti-seize compound on repeated assemblies.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778591463,"sku":"PF-STD-M3-SS-MF-20","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/pcb-standoff-male-female-schematic_a3ea50a0-ed64-4f8d-bd4b-49fc6f622591.png?v=1787757434"},{"product_id":"m3-stainless-steel-304-hex-standoff-female-female-10mm","title":"M3 Stainless Steel 304 Hex Standoff, Female-Female, 10mm","description":"\u003cp class=\"pf-crumbs\"\u003e\u003ca href=\"\/\"\u003eHome\u003c\/a\u003e › \u003ca href=\"\/collections\/pcb-standoffs\"\u003ePCB Standoffs\u003c\/a\u003e › \u003cspan\u003eM3 Stainless Steel 304 Hex Standoff, Female-Female, 10mm\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eM3 Stainless Steel 304 Hex Standoff, Female-Female, 10mm\u003c\/strong\u003e — a hex standoff in Stainless Steel 304 with female threads at both ends. Used to space a printed circuit board off its chassis, to stack boards at a fixed pitch, and to mount panels and covers inside an enclosure.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eThread size\u003c\/th\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread pitch\u003c\/th\u003e\n\u003ctd\u003e0.5 mm (coarse)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 mm (0.394 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAcross flats\u003c\/th\u003e\n\u003ctd\u003e5.5 mm (0.217 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThread configuration\u003c\/th\u003e\n\u003ctd\u003eFemale-Female\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBody shape\u003c\/th\u003e\n\u003ctd\u003eHex\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eStainless Steel 304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003ePlain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStrength grade \/ class\u003c\/th\u003e\n\u003ctd\u003eA2-70\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandards\u003c\/th\u003e\n\u003ctd\u003eDIN 6334\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax continuous temperature\u003c\/th\u003e\n\u003ctd\u003e400 °C (752 °F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRoHS\u003c\/th\u003e\n\u003ctd\u003eCompliant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit weight\u003c\/th\u003e\n\u003ctd\u003e2.077 g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStandard pack\u003c\/th\u003e\n\u003ctd\u003e100 pcs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHTS classification\u003c\/th\u003e\n\u003ctd\u003e7318.15.2000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eInstallation reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearance hole:\u003c\/strong\u003e 3.4 mm (0.134 in) — ISO 273 medium fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTap drill for M3:\u003c\/strong\u003e 2.5 mm (0.098 in) at 75% thread engagement\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNearest imperial thread:\u003c\/strong\u003e #4-40 — similar in diameter but \u003cem\u003enot interchangeable\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eAbout Stainless Steel 304\u003c\/h3\u003e\u003cp\u003e304 stainless resists general atmospheric and indoor corrosion and is non-magnetic in the annealed condition. It is not the right choice for salt spray or chloride exposure — 316 is. Stainless threads can gall under speed or load; back off the driver and use an anti-seize compound on repeated assemblies.\u003c\/p\u003e\u003ch3\u003eRelated reference\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/fastener-standards-cross-reference-asme-iso-and-din\"\u003eFastener standards cross-reference: ASME, ISO and DIN\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/tap-drill-size-chart-metric-unc-and-unf\"\u003eTap drill size chart — metric, UNC and UNF\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/metric-to-imperial-fastener-conversion\"\u003eMetric to imperial fastener conversion\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/bolt-head-markings-and-grade-chart\"\u003eBolt head markings and grade chart\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/pcb-standoffs\"\u003eAll pcb standoffs\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/pages\/reference\"\u003eAll reference charts\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eNeed a quantity, a length or a material that is not listed? \u003ca href=\"\/pages\/contact-us\"\u003eSend us the specification\u003c\/a\u003e and we will source it.\u003c\/p\u003e","brand":"Planet Fasteners","offers":[{"title":"100 pcs","offer_id":52522778624231,"sku":"PF-STD-M3-SS-FF-10","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0804\/6012\/0295\/files\/pcb-standoff-female-female-schematic_528b9475-8b09-4bcd-ab6e-29f0da11551e.png?v=1787757435"}],"url":"https:\/\/planetfasteners.com\/collections\/pcb-standoffs.oembed","provider":"Planet Fasteners","version":"1.0","type":"link"}